News

Use in potentially explosive atmospheres in accordance with ATEX and IECEx … Use in ATEX / IECEx Zone 1

Housing purge control flow

The power supply of the gas analyzer is provided via the purging and monitoring unit of the housing purging.

• The power supply to the gas analyzer may only be released from the purging and monitoring unit after the successful initial purge.

• The purging and monitoring unit monitors the overpressure inside the housing and de-energizes the gas analyzer if the level is below the minimum overpressure (e.g. due to a leakage or purge gas supply failure).

Sequence of the purging and monitoring unit The gas analyzer is powered from the purging and monitoring unit, i.e. the purging and monitoring unit prevents the gas analyzer from being energized before the purge is completed.

The flow sequence of the purging and monitoring unit is as follows:

1. After the start of the sequence, the purge gas flow and overpressure in the monitor are monitored by the purging and monitoring unit.

2. If the minimum flow rate of the purge gas and the overpressure are within the specified limits (see Purge parameters for pressurized enclosure on page 10), the purge timer (initial purge time) can be started;

3. After the initial purge time has elapsed, the power supply is released for the gas analyzer.

4. In the event of an error in one of the sequence steps, the controller must be set up to be reset to the beginning.

This sequence is presented in Figure 4.

Each state of the system is defined in response to the inputs of the monitor. The states are unique. Transitions between the states are only allowed along the paths defined by the arrows and towards the arrows.

The logical conditions for each state are defined by the following boolean logical expressions:

Use in potentially explosive atmospheres in accordance with ATEX and IECEx Use in ATEX / IECEx Zone 2

Introduction

This part of the Operating Instruction contains information of installation, operation and maintenance of the analyzer, ATEX Zone 2 version.

A Non-hazardous area B Hazardous area (ATEX IECEx Zone 2)

1 Power supply TRACO POWER TEX120, either in ATEX Zone 2 or outside the hazardous area

2 Power supply Pepperl+Fuchs PSC2.PS.GR.18.36.17.D-Y0168136, either n

ATEX /IECEx Zone 2 or outside the hazardous area

3 Transmitter unit

4 Connection box

5 Cable glands

6 Purge gas connections

7 Receiver unit

The analyzer consists of three separate modules:

• Transmitter unit with purge fittings and connection box with terminals for the connection of mains and signal cables as well as optional inputs.

• Receiver unit with purge fittings.

• Power supply unit (either TRACO POWER TEX120 or Pepperl+Fuchs PSC2.PS.GR.18.36.17.D-Y0168136)

Standards and directives

All gas analyzer models comply with the regulations of the

European Directive 2014/34/EU (ATEX Directive) / IECEx

scheme, and they are manufactured in accordance with the

following standards:

• EN/IEC 60079-0

• EN/IEC 60079-15

• EN/IEC 60079-28

• EN/IEC 60079-31

The gas analyzer must be designed, installed and operated in accordance with the following standards and directives:

• EN/IEC 60079-14

• EN/IEC 60079-17

• EN/IEC 60079-19

Note

The full designation of the applied standards, including the date of issue, is included in the declaration of conformity supplied with the device.
Related recommendations:
SKKH330/18E
VICKERS 9VB29RS20CM11
Power Supply QUINT-PS/1AC/24DC/20
Rorze RD-323MS
Reliance Electric UVZ3037 – VZ3000
Linmot S01-72/600
Pepperl+Fuchs HIC2025
HUTTINGER PFG5000
P+F KCD2-STC-EX1
BOSCH VM300
WOODWARD EASYGEN-1000
PHOENIX QUINT-PS
KEPCO BOP-20-20M
Fuji 2MBI300N-060 
RADISYS ERNI 9609
more……

Guaranteed safe – Quality control and equipment protection for your benefit – simple, economical, dependable

Sartorius metal detectors serve diverse branches of industry: chemicals, plastics, recycling, rubber, wood, textiles, nonmetallic minerals, power generation, mining, tobacco, clay and foods.

Evaluation electronics

Premium model: Electronic evaluator, MDB-8E

Multi-channel technology

Microprocess-oriented

Flexible phase adjustment

Menu-driven operation

Continuous self-test 40 product-type memory

locations 100% traceable documentation

Advanced internal function control

Standard model: MDB-5E

Extra-economical single-channel unit

Microprocessorized

Manual phase adjustment

Extremely simple function-key operation

Internal function control

While the food industry gives maximum priority to consumer protection, most other branches of industry attach more importance to protecting their expensive production equipment from damage and their personnel from injury. Like our very successful DISCOVERY, DISCOVERY PLUS and the new OBSERVER series, the alternatives dealt with here provide equipment protection to the satisfaction of our “habitually” high standards.

MDB-C|MDB-R

This MDB-C|MDB-R search coil in a fall-shaft assembly with diverter-valve ejector protects grinding mills, kneaders, rollers and extruders. Its typical areas of application include the plastics, chemicals and food industries.

MDB-C

An MDB-C search coil with conveying belt enables maximum accuracy of detection, even for large clear heights. It protects processing equipment in the chemicals, textiles and chipboard sectors.

MDB-R

These made-to-measure MDB-R round gates for merchantable bowls and logs in the timber industry are also used in pneumatic conveying systems serving the textile industry

MDB-D

MDB-D search coils offer all the advantages of dependable detection coupled with ease of installation, thanks to a split detector requiring no dismantling of the belt to install it.

MDB-US|MDB-UB

The underbelt coil MDB-US| MDB-UB, with its particular ease of installation and good detection sensitivity, guarantees an optimal value-formoney ratio.

MDB-D

An MDB-D search coil protects downstream mills and crushers from the dreaded risk of damage in the recycling, plastic, chemical, tobacco, clay and wood industries.

MDB-DL|MDB-DH

Our huge MDB-DL and MDB-DH search coils are designed for use in open-pit mines, power plants, mining and the timber industry, where they protect excavators, grinding mills, chippers and crushers
Related recommendations:
CB1086DPA0000
METSO IOP303
SEMIKRON SKKH330
3RG4143-6AD00
MSXB048-02-E2
A413511-02 – 2
ALFA LAVA 3183062451
FANUC A16B-1000-0220
AAP3798102-00031
9VB29RS20CM11
TECHNOLOGY 10338-53100
CVX-1243-MC2
ECOSTEP 100-AJ-000-000
M-AIR2
1070080680
more……